To build Dr.
Vanski's EZ Ultimate Racer (UR) Interface you will need the following:
1 x Scalextric C8147 RMS Multi-Lane extension
1 x DB25 male parallel connector
1 x 1/8" stereo headphone female mini-jack
1 x 20' stereo walkman headphone extension cable
3 x short pieces of coloured wire (red, green, and black)
6 x short pieces of narrow heat shrink tubing
2 x short pieces of larger heat shrink tubing
Cost:
About $45 for parts and an hour of your time. I got the wire, heat
shrink tubing, and connectors at my local Radio Shack. Your local Scalextric dealer
can get you the C8147, or order it online from any reputable mail order slot car store.
Instructions:
- Connect the wires to pins 25 (black), 12 (red), and 10 (green) of the
DB25 connector. Apply a drop of solder even with crimped connectors to make sure you
have a nice solid connection.
- Connect the DB25 plug to your parallel port and check that UR
"sees" the connections. I have set lane 1 to detect as pin 10 and lane 2
to detect as pin 12. The green dots in the Setup screen should turn grey when the
wire from pin 25 touches either the wire from pin 10 or 12. If this all works then
unplug the DB25 connector from your computer, heat shrink the end of each wire, and then
put the bigger heat shrink tubing around all 3 wires to hold them together nicely.
- Slide the insulating shield for the stereo headphone mini-jack over
all three wires. Slide one piece of larger heat shrink tubing over all three
wires. Slide one piece of smaller heat shrink tubing over each individual
wire. Connect the red wire to the copper connector on the mini-jack, the green wire
to the silver connector, and the black wire to the long piece coming out of the
mini-jack. Apply a drop of solder to make sure you have a good connection.
- Push the stereo mini-plug from C8147 into the mini-jack.
Connect the DB25 to your computer. Slide a slot car over the switch in the C8147 and
again check that the green dots turning grey in the Setup screen of UR.
- Once you are sure this works for each lane, unplug the C8147 and DB25
connectors and heat shrink each individual wire. Then heat shrink all three wires
together on the mini-jack. Screw the insulating cover back onto the mini-jack.
- Install the C8147 into your track. Connect it to the headphone
extension cable. Run the extension cable over to your computer and plug it into the
mini-jack. Plug the DB25 connector into your computer, fire up Ultimate Racer, and
RACE!
- Place the C8147 on a slow part of your circuit, or in a braking
zone. This will ensure that the car's guide is planted firmly in the slot as it
crosses this section of track. In this case, the C8147 is located just in front of
the 2 cars on the track.
Thank-you:
Thanks to Bonnie-Sue for putting up with my track in our tiny apartment on
weekends, and sharing my passion for racing in our living room. Her '70 Scalextric
Mustang rips up our track as she humbles my friends with her driving skills.
Thanks to Joe, John, and Ernie at http://www.raceworldcanada.com/ for their excellent
slot car racing advice and recommendations. It is the place to go in Toronto
for cars, track and slot car performance parts.
Thanks to Les Kushner at www.mainlinehobbies.com for selling me the C8147 from their store
track and shipping it to Toronto so promptly.
Last but not least: thanks to Pierrick for coding UR. His work has allowed me
to design some very cool circuits to fit our confined space. It is an efficient yet
powerful program that runs on modest hardware resources and has added a new dimension of
fun to my slot car racing experience. If you enjoy designing tracks, timing your
races to 1/1000th of a second, and racing in tournaments with your friends using Ultimate
Racer as much as I do(I know that you will!!), be sure to help out the Multiple Sclerosis Society in your country with a modest gift.
This is a good cause that is important to invalids.
|